Home» Online Test » Civil Engineering » Drawing Online Test » Paper 1 » Paper 2 » Paper 3 0% Sorry, time's up. To complete the online test, please restart it. Created by Vikash chaudhary This is a FREE online test. Beware of scammers who ask for money to attend this test. Get fresh, new questions in each attempt. Total Questions: 30 Time Allotted: 30 minutes Passing Score: 50% Randomization: Yes Certificate: No Do not refresh the page! 👍 All the best! 1 / 30 1. During drawing, stock of T-square is placed: a) Adjoining the working edge of the board b) Adjoining the sliding edge of the board c) Surface of the board d) None of the above 2 / 30 2. The main purpose of the working drawing is: a) To facilitate the construction at the site b) To prepare the bill of quantities and detailed estimate c) To record the design implementation d) All of the above 3 / 30 3. In case of perspective projection, the picture plane is placed: a) Between eye and object b) Outside of eye towards eye c) Outside of the object towards the object d) All of the above 4 / 30 4. French curves are used to draw: a) Regular curves b) Circle c) Irregular curves d) None of these 5 / 30 5. A cylinder can be created by drawing a rectangular shape then the........ tool: a) Sweep b) Revolve c) Extrude d) None of the above 6 / 30 6. The symbol indicates: a) Bamboo b) Mango c) Blackberry d) Tree 7 / 30 7. Free-hand sketching can be done only if one has: a) Proper proficiency b) Good practice c) Good intuition d) All of the above 8 / 30 8. ...... is used for setting short equal distances. a) Compass b) Bow divider c) Scale d) Lengthening bar 9 / 30 9. Axonometric drawing is a drawing like: a) Parallel to the plane b) Perpendicular to the plane c) Inclined to the plane d) All of the above 10 / 30 10. In orthographic projection, which one has all three views the same: a) Cube b) Circle c) Sphere d) Both (a) and (c) of above 11 / 30 11. In italic lettering, the direction of the letters is at: a) 60° b) 90° c) 75° d) 120° 12 / 30 12. The dimension system is unidirectional if: a) Dimensions in the drawing sheet can be read from anywhere on the drawing sheet b) Dimensions in the drawing sheet can be read from the bottom edge of the drawing sheet c) Dimensions in the drawing sheet can be read from the bottom and right-hand edge of the drawing sheet d) Dimensions cannot be read 13 / 30 13. As-built drawing is normally constructed...... the construction a) Before construction b) Simultaneously with construction c) After construction d) All of the above 14 / 30 14. The dimension lines are marked in a building drawing with: a) Arrows b) Ticks or dots c) Arrows or ticks d) Arrows or dots 15 / 30 15. The following is not included in the title block of a drawing sheet: a) Sheet no. b) Scale c) Size of sheet d) Method of protection 16 / 30 16. Pencil of...... grade sharpened in the form of...... is used for sketching. a) Soft & conical point b) Low and conical point c) Hard & conical point d) Chisel & conical point 17 / 30 17. Set squares are used for drawing: a) Vertical lines b) Inclined lines c) Parallel lines d) All of the above 18 / 30 18. Dashed (dotted) line is used for indication: a) Edge of the object b) Hidden edge of the object c) Centre line of the object d) All of the above 19 / 30 19. Hatching line is a line which makes an angle of 45° with: a) Horizontal b) Vertical c) Main line of the section d) All of the above 20 / 30 20. One plane projection is: a) Axonometric projection b) Oblique projection c) Both (a) and (b) above d) None of the above 21 / 30 21. Working drawing is prepared not for: a) Bill of quantities b) Estimation c) Layout d) Specification 22 / 30 22. Which is not a pictorial projection? a) Oblique projection b) Orthographic projection c) Trigonometric d) Axonometric projection 23 / 30 23. The section obtained when the section plane is inclined to the axis of the cone but parallel to one of the generators of a cone is called: a) A hyperbola b) A circle c) An ellipse d) A parabola 24 / 30 24. Trench plan of a building shows: a) Location and dimension of footing in the horizontal plane b) Location and depth of the foundation c) Locating footing size and depth of foundation d) Depth of excavation for the foundation 25 / 30 25. What is the slant for the letter shown? K80° a) 80° b) 10° c) 0° d) None of the above 26 / 30 26. Which one is not drafting equipment? a) Drafter b) Dust cloth c) Scale d) None of the above 27 / 30 27. The following are polyhedron except: a) Prism b) Pyramid c) Cube d) Cylinder 28 / 30 28. The main objective of writing letters/alphabets on the drawing is to make the drawing: a) More fantastic b) More informative c) More expensive d) All of the above 29 / 30 29. Circles of small radii are drawn by means of a: a) Straight bar b) Bow compass c) Lengthening bar d) Drop compass 30 / 30 30. The most important material for drawing is: a) Pencil and eraser b) Eraser & paper c) Paper & pencil d) None of the above Please provide accurate information so we can send your Achievement Certificate by mail. NameEmailPhone Number Your score isShare your achievement! LinkedIn Facebook 0% Restart Test Please provide your feedback. Thank you for your valuable feedback. Send feedback Buy Drawing MCQ PDF for Offline Study