Home» Online Test » Civil Engineering » Drawing Online Test » Paper 1 » Paper 2 » Paper 3 0% Sorry, time's up. To complete the online test, please restart it. Created by Vikash chaudhary This is a FREE online test. Beware of scammers who ask for money to attend this test. Get fresh, new questions in each attempt. Total Questions: 50 Time Allotted: 50 minutes Passing Score: 70% Randomization: Yes Certificate: Yes Do not refresh the page! 👍 All the best! 1 / 50 1. Free-hand sketching can be done only if one has: a) Proper proficiency b) Good practice c) Good intuition d) All of the above 2 / 50 2. The scale should never be used as a: a) Set-square b) Working edge c) Straight edge d) None of the above 3 / 50 3. In orthographic projection, projector lines are: a) Vertical lines b) Inclined lines c) Horizontal lines d) None of the above 4 / 50 4. The techniques for free-hand sketch to drawing a circle is: a) Fixing a fixed point and arc b) Fixing the perimeter c) Fixing the radius only d) None of the above 5 / 50 5. Circle and arcs of circles are drawn by means of a: a) Lengthening bar b) Divider c) Compass d) T-square 6 / 50 6. T square is used alone to draw: a) Vertical lines b) Inclined lines c) Horizontal lines d) None of the above 7 / 50 7. One plane projection is: a) Axonometric projection b) Oblique projection c) Both (a) and (b) above d) None of the above 8 / 50 8. Which line type is thin and light? a) Visible line b) Construction line c) Centre line d) All of the above 9 / 50 9. The given symbol represents: a) School b) Temple c) Church d) Catenary 10 / 50 10. The space between two sentences should be left equal to: a) Height of the letter b) Twice the height of the letter c) 1.5 times the height of the letter d) None of the above 11 / 50 11. The section obtained when the section plane is inclined to the axis of the cone but parallel to one of the generators of a cone is called: a) A hyperbola b) A circle c) An ellipse d) A parabola 12 / 50 12. To draw or measure angles...... is used. a) Set-square b) T-square c) Protractor d) All of the above 13 / 50 13. The solid which is generated by the revolution of a rectangle about one of its sides which remains fixed is called: a) A prism b) A pyramid c) A cylinder d) A cone 14 / 50 14. The diameter of the semi-circle is called: a) Diameter of protractor b) Base of protractor c) Length of protractor d) None of the above 15 / 50 15. 9H pencil is...... than the 7H pencil. a) Softer b) Harder c) Medium d) None of the above 16 / 50 16. The symbol indicates: a) Bamboo b) Mango c) Blackberry d) Tree 17 / 50 17. The unseen/inner edge of an object is represented by: a) Solid line b) Dotted line c) Hatch line d) None of the above 18 / 50 18. To remove unnecessary lines...... is used. a) Duster b) Chalk c) Sand box d) Eraser 19 / 50 19. To draw a very light line, which pencil is used? a) B b) HB c) H d) 2H 20 / 50 20. For drawing thin lines of uniform thickness, the pencil should be sharpened in the form of: a) Chisel edge b) Conical c) Pointed d) Circular 21 / 50 21. Uses of the T-square, set squares, scale, and protractor are combined in the: a) Set-square b) Drafting machine c) Compass d) None of the above 22 / 50 22. ...... is used for setting short equal distances. a) Compass b) Bow divider c) Scale d) Lengthening bar 23 / 50 23. In case of third angle projection, the plan is kept at: a) Top b) Bottom c) Side d) None 24 / 50 24. Set squares are used for drawing: a) Vertical lines b) Inclined lines c) Parallel lines d) All of the above 25 / 50 25. In engineering drawing, auxiliary views are used to show details of: a) Inclined surfaces b) Horizontal surfaces c) Vertical surfaces d) None of the above 26 / 50 26. The given symbol indicates: a) Temple b) Mosque c) Church d) Museum 27 / 50 27. Trench plan of a building shows: a) Location and dimension of footing in the horizontal plane b) Location and depth of the foundation c) Locating footing size and depth of foundation d) Depth of excavation for the foundation 28 / 50 28. What is the slant for the letter shown? K80° a) 80° b) 10° c) 0° d) None of the above 29 / 50 29. The section obtained when the section plane passes parallel to the base of a cone is called: a) An ellipse b) A parabola c) A hyperbola d) A circle 30 / 50 30. Large circle or curvatures are drawn by means of a: a) Straight bar b) Bow compass c) Divider d) Beam compass 31 / 50 31. In architectural drawing, all letters should be uniform in: a) Size and shape b) Sloped and shade c) Spacing d) All of the above 32 / 50 32. The dimension system is unidirectional if: a) Dimensions in the drawing sheet can be read from anywhere on the drawing sheet b) Dimensions in the drawing sheet can be read from the bottom edge of the drawing sheet c) Dimensions in the drawing sheet can be read from the bottom and right-hand edge of the drawing sheet d) Dimensions cannot be read 33 / 50 33. Which type of line is a part of dimension? a) Extension line b) Break line c) Cutting plane line d) Phantom line 34 / 50 34. A drawing view in which all vertical planes are represented by the horizontal lines radiated from a far-situated point, on each side of the plane, is: a) Perspective view b) Axonometric view c) Isometric view d) Oblique view 35 / 50 35. In case of unidirectional method of dimensioning, they can be read from: a) Bottom side of the drawing sheet only b) Right side of the drawing sheet only c) Top side of the drawing sheet only d) Left side of the drawing sheet only 36 / 50 36. The approval of design, drawing before the construction of a building in the city area of Nepal is done by: a) Village Development Committee b) District Development Committee c) Municipality d) None of the above 37 / 50 37. When a pyramid or cone is cut by a cutting plane parallel to its base, the remaining portion thus obtained after removing the top portion is called: a) A prism b) A frustum c) A cylinder d) None of these 38 / 50 38. Mechanical lines are types of: a) Mechanic drawing b) Line drawn with free hand c) Line drawn with drawing equipment d) None of the above 39 / 50 39. For drawing large-size circles...... is attached to the compass (>150mm). a) Straight bar b) Bow compass c) Lengthening bar d) Divider 40 / 50 40. Bisecting a line means, divide a line into.....equal part. a) Two b) Three c) Four d) None of the above 41 / 50 41. The section obtained when the section plane is inclined to the axis of the cone and cuts all the generators on either side of the apex is called: a) An ellipse b) A parabola c) A hyperbola d) A circle 42 / 50 42. In drafting machine, which one does not follow: a) Levelling machine b) T-scale c) Set square d) Divider 43 / 50 43. Axonometric drawing is a drawing like: a) Parallel to the plane b) Perpendicular to the plane c) Inclined to the plane d) All of the above 44 / 50 44. In one plane drawing, which one does not fall under: a) Orthographic b) Axonometric c) Oblique d) Dimetric 45 / 50 45. A cylinder can be created by drawing a rectangular shape then the........ tool: a) Sweep b) Revolve c) Extrude d) None of the above 46 / 50 46. Circles of small radii are drawn by means of a: a) Straight bar b) Bow compass c) Lengthening bar d) Drop compass 47 / 50 47. ...... is used for drawing curves which can't be drawn by a compass. a) Bow compass b) Protractor c) French curve d) Scale 48 / 50 48. In case of orthographic projection, the number of views generally used is: a) 2 b) 4 c) 6 d) 8 49 / 50 49. In the case of dimetric projection: a) Two sides are not equally inclined b) Two sides are equally inclined c) Two sides are parallel d) Two sides are equal 50 / 50 50. In orthographic projection, which one has all three views the same: a) Cube b) Circle c) Sphere d) Both (a) and (c) of above Please provide accurate information so we can send your Achievement Certificate by mail. NameEmailPhone Number Your score isShare your achievement! LinkedIn Facebook 0% Restart Test Please provide your feedback. Thank you for your valuable feedback. Send feedback Buy Drawing MCQ PDF for Offline Study